Leaking Gutter Joints: Why They Leak and How They’re Repaired

A leaking gutter joint is usually a worn seal, a shifted run or a blockage. Here is why it happens and how a lasting repair is done.

A leaking gutter joint usually means the seal has failed, the joint has been knocked out of line or debris is making water back up and push through the gap. Small drips can often be fixed by replacing the joint with a new part and resetting the run, rather than just smearing sealant over the top.

Why gutter joints leak

Most uPVC guttering is made of lengths joined by union brackets with a rubber seal inside. Where two lengths meet, or a length meets a corner or stop end, that seal is all that stops water escaping. It is a simple system, but it has several weak points.

  • Perished seals. Rubber hardens and cracks with age, sunlight and temperature swings.
  • Movement. Plastic expands in warm weather and contracts in the cold. If the gutter is not able to slide slightly in the joint, the seal can be pulled out of position.
  • Poor fall. A gutter that does not slope correctly holds standing water, which sits against the joint and finds any weakness.
  • Blockages. A gutter that is full of debris backs up and forces water out at the lowest or weakest point, often a joint.
  • Loose or missing brackets. Without enough support, the run sags and the joint opens.
  • Ladders, branches and storms. Knocks can crack a union or push the gutter out of line.
  • Old sealant. A previous quick fix with silicone or tape may have failed and trapped dirt.

How to spot a leaking gutter joint

You do not need to be on the roof to see the signs. Look from the ground, ideally during or just after rain.

Sign What it can tell you
Drip or stream from a joint in the rain The seal has failed or the run has moved
Dark or green streak on the wall under the joint A long-running leak
Water only drips in heavy rain A blockage or too much flow for the pipe, with the joint as the weak point
Stained or rotting fascia behind the joint Water has been getting behind the gutter for some time
Drips continue after the rain stops The gutter is holding water, so there may be a fall or sag problem

If the stain is on the wall below and the gutters overflow rather than leak, the problem is more likely a blockage. See our post on why gutters overflow for how to tell the difference.

How a leaking gutter joint is repaired

The right fix depends on what has gone wrong. A good repair starts by finding out why the joint leaks, not by covering the drip.

  1. Clear the gutter. Debris and silt are removed so the joint can be inspected and the system can flow freely.
  2. Inspect the joint and the run. We check the seal, the clips, the bracket spacing and whether the gutter has the right fall.
  3. Replace the faulty part. If the union, seal or section is damaged, it is replaced with a new part. This is different from sealing over the problem, which can hold for a while but often fails again.
  4. Reset the run. Brackets are added or adjusted so the gutter sits at the correct angle and supports its own weight.
  5. Test it. Water is run through the gutter to check that the joint is tight and the flow reaches the downpipe.

Can you seal a gutter joint with silicone?

It is possible, and sometimes it buys you a bit of time. A clean, dry, well-supported joint with a small drip may respond to a sealant designed for gutters. The trouble is that sealant is rarely a permanent fix when the real problem is movement, a perished seal or a sag. It also makes later repairs harder, because the old product has to be cleaned off first.

If you try it yourself, keep it to work you can safely reach from the ground or from a low, stable position. Anything above single storey is best left to professionals, and wet weather is the wrong time to be up a ladder.

When a leaking joint means something bigger

One drip at one joint is usually a minor repair. If several joints leak, the gutters sag in the middle or the plastic is brittle and cracking, the system may be reaching the end of its life. In that case it is worth comparing a repair with new guttering, and our guide on whether to repair or replace gutters sets out how to decide. You can also read how long uPVC gutters typically last.

It is also worth checking whether the leak has already damaged anything. Soft or stained timber behind the gutter should be looked at before it spreads. If you want to learn more about the parts involved, our article on what fascias and soffits are explains them.

Preventing joints from leaking again

  • Have the gutters cleared once a year so water does not back up.
  • Make sure the brackets are secure and evenly spaced.
  • Check the run after storms or when ladders have been leant against it.
  • Do not ignore a small drip. A minor leak that goes on for a winter can rot the timber behind it.

We repair gutters in Byfleet, Thames Ditton and Shepperton, as well as the other places listed on our areas we cover page. If a system is badly worn, we also fit new uPVC guttering through our gutter installation service.

How SuperClean Gutters can help

Our gutter repairs service deals with leaking joints, loose brackets, sagging runs and cracked sections. We carry common gutter parts on the vans and replace damaged joints with new parts rather than just sealing them. The team is fully insured, and our work is backed by our service guarantee.

Send your address and a few photos of the leak and of each guttered side, taken from below, and we will usually quote the same day.

Call or WhatsApp 07368 590868 or send photos on WhatsApp for a free quote.

Frequently asked questions

Why is my gutter leaking at the joint?

The most common reasons are a worn rubber seal, a joint that has shifted with temperature changes, a gutter without enough fall or support, and a blockage forcing water out. Finding the cause matters, because patching over the drip without fixing it often brings the leak back.

Can a leaking gutter joint cause damp?

It can. A steady drip against the wall or behind the gutter can stain brickwork and soak the fascia and eaves timber. If left for a long time, that moisture can lead to rot or damp inside. Fixing a small leak early is much easier than repairing the damage afterwards.

Is it better to replace the joint or reseal it?

Replacing a damaged joint with a new part generally gives a more lasting result. Resealing may be a short-term measure if the joint is sound and the leak is slight. If the seal has perished, or the run has moved, sealant alone is unlikely to hold.

How long does it take to fix a leaking joint?

A single joint is often a quick job once the gutter is clear and accessible, but it depends on the height, the condition of the run and whether other faults are found. We can give you a better idea once we have seen your photos.

Need your gutters sorted?

Fully insured, friendly local team. Send a few photos and we’ll usually quote the same day – free and no obligation.

In this guide

More guides from our team

Get a free, same-day quote

Send your address and a few photos from the ground – we’ll take it from there.